26.2 Auto-Saving

Emacs periodically saves all files that you are visiting; this is called auto-saving. Auto-saving prevents you from losing more than a limited amount of work if the system crashes. By default, auto-saves happen every 300 keystrokes, or after around 30 seconds of idle time. See section `Auto-Saving: Protection Against Disasters' in The GNU Emacs Manual, for information on auto-save for users. Here we describe the functions used to implement auto-saving and the variables that control them.

Variable: buffer-auto-save-file-name

This buffer-local variable is the name of the file used for auto-saving the current buffer. It is nil if the buffer should not be auto-saved.

buffer-auto-save-file-name => "/xcssun/users/rms/lewis/#backups.texi#"

Command: auto-save-mode arg

When used interactively without an argument, this command is a toggle switch: it turns on auto-saving of the current buffer if it is off, and vice versa. With an argument arg, the command turns auto-saving on if the value of arg is t, a nonempty list, or a positive integer. Otherwise, it turns auto-saving off.

Function: auto-save-file-name-p filename

This function returns a non-nil value if filename is a string that could be the name of an auto-save file. It assumes the usual naming convention for auto-save files: a name that begins and ends with hash marks (`#') is a possible auto-save file name. The argument filename should not contain a directory part.

(make-auto-save-file-name) => "/xcssun/users/rms/lewis/#backups.texi#" (auto-save-file-name-p "#backups.texi#") => 0 (auto-save-file-name-p "backups.texi") => nil

The standard definition of this function is as follows:

(defun auto-save-file-name-p (filename) "Return non-nil if FILENAME can be yielded by..." (string-match "^#.*#$" filename))

This function exists so that you can customize it if you wish to change the naming convention for auto-save files. If you redefine it, be sure to redefine the function make-auto-save-file-name correspondingly.

Function: make-auto-save-file-name

This function returns the file name to use for auto-saving the current buffer. This is just the file name with hash marks (`#') prepended and appended to it. This function does not look at the variable auto-save-visited-file-name (described below); callers of this function should check that variable first.

(make-auto-save-file-name) => "/xcssun/users/rms/lewis/#backups.texi#"

The standard definition of this function is as follows:

(defun make-auto-save-file-name () "Return file name to use for auto-saves \ of current buffer.." (if buffer-file-name (concat (file-name-directory buffer-file-name) "#" (file-name-nondirectory buffer-file-name) "#") (expand-file-name (concat "#%" (buffer-name) "#"))))

This exists as a separate function so that you can redefine it to customize the naming convention for auto-save files. Be sure to change auto-save-file-name-p in a corresponding way.

Variable: auto-save-visited-file-name

If this variable is non-nil, Emacs auto-saves buffers in the files they are visiting. That is, the auto-save is done in the same file that you are editing. Normally, this variable is nil, so auto-save files have distinct names that are created by make-auto-save-file-name.

When you change the value of this variable, the new value does not take effect in an existing buffer until the next time auto-save mode is reenabled in it. If auto-save mode is already enabled, auto-saves continue to go in the same file name until auto-save-mode is called again.

Function: recent-auto-save-p

This function returns t if the current buffer has been auto-saved since the last time it was read in or saved.

Function: set-buffer-auto-saved

This function marks the current buffer as auto-saved. The buffer will not be auto-saved again until the buffer text is changed again. The function returns nil.

User Option: auto-save-interval

The value of this variable specifies how often to do auto-saving, in terms of number of input events. Each time this many additional input events are read, Emacs does auto-saving for all buffers in which that is enabled.

User Option: auto-save-timeout

The value of this variable is the number of seconds of idle time that should cause auto-saving. Each time the user pauses for this long, Emacs does auto-saving for all buffers in which that is enabled. (If the current buffer is large, the specified timeout is multiplied by a factor that increases as the size increases; for a million-byte buffer, the factor is almost 4.)

If the value is zero or nil, then auto-saving is not done as a result of idleness, only after a certain number of input events as specified by auto-save-interval.

Variable: auto-save-hook

This normal hook is run whenever an auto-save is about to happen.

User Option: auto-save-default

If this variable is non-nil, buffers that are visiting files have auto-saving enabled by default. Otherwise, they do not.

Command: do-auto-save &optional no-message current-only

This function auto-saves all buffers that need to be auto-saved. It saves all buffers for which auto-saving is enabled and that have been changed since the previous auto-save.

Normally, if any buffers are auto-saved, a message that says `Auto-saving...' is displayed in the echo area while auto-saving is going on. However, if no-message is non-nil, the message is inhibited.

If current-only is non-nil, only the current buffer is auto-saved.

Function: delete-auto-save-file-if-necessary

This function deletes the current buffer's auto-save file if delete-auto-save-files is non-nil. It is called every time a buffer is saved.

Variable: delete-auto-save-files

This variable is used by the function delete-auto-save-file-if-necessary. If it is non-nil, Emacs deletes auto-save files when a true save is done (in the visited file). This saves disk space and unclutters your directory.

Function: rename-auto-save-file

This function adjusts the current buffer's auto-save file name if the visited file name has changed. It also renames an existing auto-save file. If the visited file name has not changed, this function does nothing.

Variable: buffer-saved-size

The value of this buffer-local variable is the length of the current buffer, when it was last read in, saved, or auto-saved. This is used to detect a substantial decrease in size, and turn off auto-saving in response.

If it is -1, that means auto-saving is temporarily shut off in this buffer due to a substantial decrease in size. Explicitly saving the buffer stores a positive value in this variable, thus reenabling auto-saving. Turning auto-save mode off or on also updates this variable, so that the substantial decrease in size is forgotten.

Variable: auto-save-list-file-name

This variable (if non-nil) specifies a file for recording the names of all the auto-save files. Each time Emacs does auto-saving, it writes two lines into this file for each buffer that has auto-saving enabled. The first line gives the name of the visited file (it's empty if the buffer has none), and the second gives the name of the auto-save file.

When Emacs exits normally, it deletes this file; if Emacs crashes, you can look in the file to find all the auto-save files that might contain work that was otherwise lost. The recover-session command uses this file to find them.

The default name for this file specifies your home directory and starts with `.saves-'. It also contains the Emacs process ID and the host name.

Variable: auto-save-list-file-prefix

After Emacs reads your init file, it initializes auto-save-list-file-name (if you have not already set it non-nil) based on this prefix, adding the host name and process ID. If you set this to nil in your init file, then Emacs does not initialize auto-save-list-file-name.