GDB can print parts of your program's source, since the debugging information recorded in the program tells GDB what source files were used to build it. When your program stops, GDB spontaneously prints the line where it stopped. Likewise, when you select a stack frame (see section Selecting a frame), GDB prints the line where execution in that frame has stopped. You can print other portions of source files by explicit command.
If you use GDB through its GNU Emacs interface, you may prefer to use Emacs facilities to view source; see section Using GDB under GNU Emacs.
To print lines from a source file, use the
l). By default, ten lines are printed.
There are several ways to specify what part of the file you want to print.
Here are the forms of the
list command most commonly used:
listcommand, this prints lines following the last lines printed; however, if the last line printed was a solitary line printed as part of displaying a stack frame (see section Examining the Stack), this prints lines centered around that line.
By default, GDB prints ten source lines with any of these forms of
list command. You can change this using
set listsize count
listcommand display count source lines (unless the
listargument explicitly specifies some other number).
list command with RET discards the argument,
so it is equivalent to typing just
list. This is more useful
than listing the same lines again. An exception is made for an
argument of `-'; that argument is preserved in repetition so that
each repetition moves up in the source file.
In general, the
list command expects you to supply zero, one or two
linespecs. Linespecs specify source lines; there are several ways
of writing them, but the effect is always to specify some source line.
Here is a complete description of the possible arguments for
Here are the ways of specifying a single source line--all the kinds of linespec.
listcommand has two linespecs, this refers to the same source file as the first linespec.
listcommand that has two, this specifies the line offset lines down from the first linespec.
There are two commands for searching through the current source file for a regular expression.
Executable programs sometimes do not record the directories of the source files from which they were compiled, just the names. Even when they do, the directories could be moved between the compilation and your debugging session. GDB has a list of directories to search for source files; this is called the source path. Each time GDB wants a source file, it tries all the directories in the list, in the order they are present in the list, until it finds a file with the desired name. Note that the executable search path is not used for this purpose. Neither is the current working directory, unless it happens to be in the source path.
If GDB cannot find a source file in the source path, and the object program records a directory, GDB tries that directory too. If the source path is empty, and there is no record of the compilation directory, GDB looks in the current directory as a last resort.
Whenever you reset or rearrange the source path, GDB clears out any information it has cached about where source files are found and where each line is in the file.
When you start GDB, its source path includes only `cdir'
and `cwd', in that order.
To add other directories, use the
directory dirname ...
dir dirname ...
If your source path is cluttered with directories that are no longer of interest, GDB may sometimes cause confusion by finding the wrong versions of source. You can correct the situation as follows:
directorywith no argument to reset the source path to empty.
directorywith suitable arguments to reinstall the directories you want in the source path. You can add all the directories in one command.
You can use the command
info line to map source lines to program
addresses (and vice versa), and the command
disassemble to display
a range of addresses as machine instructions. When run under GNU Emacs
info line command causes the arrow to point to the
line specified. Also,
info line prints addresses in symbolic form as
well as hex.
info line linespec
listcommand (see section Printing source lines).
For example, we can use
info line to discover the location of
the object code for the first line of function
(gdb) info line m4_changequote Line 895 of "builtin.c" starts at pc 0x634c and ends at 0x6350.
We can also inquire (using
*addr as the form for
linespec) what source line covers a particular address:
(gdb) info line *0x63ff Line 926 of "builtin.c" starts at pc 0x63e4 and ends at 0x6404.
info line, the default address for the
is changed to the starting address of the line, so that `x/i' is
sufficient to begin examining the machine code (see section Examining memory). Also, this address is saved as the value of the
$_ (see section Convenience variables).
The following example shows the disassembly of a range of addresses of HP PA-RISC 2.0 code:
(gdb) disas 0x32c4 0x32e4 Dump of assembler code from 0x32c4 to 0x32e4: 0x32c4 <main+204>: addil 0,dp 0x32c8 <main+208>: ldw 0x22c(sr0,r1),r26 0x32cc <main+212>: ldil 0x3000,r31 0x32d0 <main+216>: ble 0x3f8(sr4,r31) 0x32d4 <main+220>: ldo 0(r31),rp 0x32d8 <main+224>: addil -0x800,dp 0x32dc <main+228>: ldo 0x588(r1),r26 0x32e0 <main+232>: ldil 0x3000,r31 End of assembler dump.
Some architectures have more than one commonly-used set of instruction mnemonics or other syntax.
set disassembly-flavor instruction-set
x/icommands. Currently this command is only defined for the Intel x86 family. You can set instruction-set to either
att. The default is
att, the AT&T flavor used by default by Unix assemblers for x86-based targets.
Go to the first, previous, next, last section, table of contents.